Etchweld
Self etching weld-through primer for steel and alloys.
Name | Price | Buy |
---|---|---|
Etchweld - 500ml aerosol | £12.95 | |
Etchweld - 1ltr pail | £22.95 | |
Etchweld - 5ltr pail | £75.95 |
Etchweld is an etching primer corrosion protection spray
Etchweld is a single pack high-performance self-etching primer that provides ultra-high levels of adhesion to steel substrates.
Etchweld protects surfaces from corrosion and promotes superb adhesion for an enormous range of intermediate and top coats, even increasing the durability of powder coating.
Etchweld can be used on some non-metallic substrates, but tests should be conducted before use.
Etchweld can be used as an adhesion promoter for two pack fillers, putties and stoppers. Unlike other etch primers, Etchweld also provides a weld-through function.
Etchweld will also provide high levels of adhesion for coatings applied to non-ferrous substrates such as aluminium and zinc treated surfaces.
Etchweld is free of heavy metals and chromates.
A Comparison
Etchweld is a single pack high-performance self-etching primer that provides ultra-high levels of adhesion to steel substrates. Etchweld protects surfaces from corrosion and promotes superb adhesion for an enormous range of intermediate and topcoats, even increasing the durability of powder coating. Etchweld can be used on some non-metallic substrates but tests should be conducted before use.
Etchweld can be used as an adhesion promoter for two pack fillers, putties and stoppers. Unlike other etch primers, Etchweld also provides a weld-through function.
Etchweld will also provide high levels of adhesion for coatings applied to non-ferrous substrates such as aluminium and zinc treated surfaces. Etchweld is free of heavy metals and chromates.
Quick Guide
Outstanding adhesion to steel, aluminium, and galvanised surfaces.
Replaces traditional low adhesion primers.
Improves durability of a huge range of paints and powder coatings.
Excellent weld-through property allows corrosion protection of flanges and seams before assembly. Does not cause porous welds.
Easy-to-use air drying.
Brush, spray or aerosol applied.
Availability:
500ml aerosol
1 litre pail
5 litre pail
How To Use
Aerosol:
Always shake the can vigorously for two minutes before use. Non-aerosol product should be stirred thoroughly before use and can be thinned up to 50% with cellulose thinners.
Weld Through:
Ensure that the surfaces are clean and free of contaminants such as corrosion, grease, oil, and paint. Where Etchweld is to remain uncoated in weld-through applications such as face-to-face flanges, two light coats applied at a distance of around 25 cm are recommended at 7 – 10 minute intervals. Before welding it is important to ensure that full flash-off of solvents has occurred. At an ambient temperature of 20 degrees C, one hour is sufficient. In cold conditions allow up to three hours.
Etchweld can be MIG, TIG, ARC or gas welded. To ensure instant and perfect welds when using spot welding equipment, clamp components together initially using clamping equipment such as quick release welding clamps, mole grips or g-cramps etc. Ensure welder setting is adjusted by testing on scrap steel of identical gauge as the work-piece. MIG welders should be set to produce an even, constant arc, spitting unstable arc is indicative of too high wire speed and can be eliminated by adjustment. After assembly of hollow sections seal seams with seam sealer or further paint coatings, internal sections should be wax injected.
Etch Primer:
Adhesion promoter for:
Cellulose, synthetic, two-pack, water borne, water based, stoving enamel, powder coat, alkyd etc.
Etchweld should be applied as a uniform coating at around 25cm from the degreased, clean surface, and normally allowed to cure for a period of 30 – 45 minutes before over coating, shorter times are acceptable when using most top coats, however for thick film coatings allow up to one hour before top coat application. Etchweld will continue to chemically anchor to the substrate under paint films for periods of up to three hours. As with any paint system it is good practice to test paint systems at small scale before use.
Shipping Info
This product is hazardous and can only be shipped to selected destinations within Europe.
To find out if you can have this shipped please place it in your basket then go to the checkout and select your country, the price of shipping will be displayed at the bottom right of the page.
We aim to ship all orders within 3-5 business days. Thank you for your patience and understanding.
Related products
-
Epoxy-Mastic
Heavy-duty two-part waterproof tough coating for steel and alloys.
-
Electrox
Zinc-rich anti-corrosion coating for steel.
Free UK Delivery
Orders over £60
Need assistance?
Call 01277 65 88 99
Award-Winning Products